Outdoor LED Power Supply, 150W Manufacturer

Outdoor LED Power Supply, 150W

Request a Quote

View All: http://co2-lasertube.com/4-1-laser-power-supply.html

Features:
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
Outdoor power supply is up to 94% efficient
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67/IP65 design for outdoor lighting supply
Type HL LED Driver for use in Class, Division 2 hazardous location luminaires
Three-in-one dimming function (1~10Vdc or PWM signal or resistance)
Suitable for LED lighting and street lighting applications
Compliance to worldwide safety regulations for LED power supply
Suitable for dry / damp /wet locations

Technical Specification:

MODEL		PW150-24D-063A-MW
OUTPUT	DC VOLTAGE	24V
	CONSTANT CURRENT REGION Note.4	12-24V
	RATED CURRENT	6.3A
	RATED POWER	151.2 W
	RIPPLE & NOISE (max.) Note.2	150mVp-p
	VOLTAGE ADJ. RANGE Note.6	22 -27V
	CURRENT ADJ. RANGE	Can be adjusted by internal potentiometer
	CURRENT ADJ. RANGE	3.8-6.3A
	VOLTAGE TOLERANCE Note.3	±1.0%
	LINE REGULATION	±0.5%
	LOAD REGULATION	±0.5%
	SETUP, RISE TIME Note.8	1000ms,50ms/115VAC 500ms,50ms/230VAC at full load
	HOLD UP TIME ( Typ . )	16ms at full load 230VAC /115VAC
INPUT	VOLTAGE RANGE Note.5	90 -305VAC 127-431VDC
	FREQUENCY RANGE	47~63Hz
	POWER FACTOR ( Typ . )	PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
	TOTAL HARMONIC DISTORTION	THD< 20% when output loading ≥ 60% at 115VAC/230VAC input and output loading ≥ 75% at 277VAC input
	EFFICIENCY ( Typ . )	93%
	AC CURRENT ( Typ . )	1.7A /115VAC 0.75A/230VAC 0.7A/277VAC
	INRUSH CURRENT ( Typ . )	COLD START 65A( twidth =425 m s measured at 50% Ipeak ) at 230VAC
	LEAKAGE CURRENT	<0.75mA/277VAC
PROTECTION	OVER CURRENT	95 - 108%
	OVER CURRENT	Protection type: Constant current limiting, recovers automatically after the cause of fault is removed
	SHORT CIRCUIT	Constant current limiting, recovers automatically after the cause of fault is removed
	OVERVOLTAGE	28-34V
	OVERVOLTAGE	Protection type: Shut down o/p voltage with auto-recovery or re-power on to recovery
	OVER TEMPERATURE	Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT	WORKING TEMP.	-40 ~ 70℃ (Refer to " Derating Curve")
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ 80℃ , 10-95% RH
	TEMP. COEFFICIENT	± 0.03% ℃ (0-50℃ )
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X,Y,Z axes
SAFETY& EMC	SAFETY STANDARDS Note.7	UL8750, CSAC22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP67 ,J61347-1, J61347- 2-13 approved; design refer to UL60950-1, TUV EN60950-1
	WITHSTAND VOLTAGE	I/P-0/P:3.75KVAC I/P-FG:2KVAC 0/P-FG : 1.5KVAC
	ISOLATION RESISTANCE	I/P-O/P, I/P-FG , 0/P-FG:100M Ohms/500VDC/25℃70% RH
	EMC EMISSION	Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≥60% load); EN61000-3-3
	EMC IMMUNITY	Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547, EN55024 , light industry level (surge 4KV), criteria A
OTHERS	MTBF	192.2K hrs min. MIL-HDBK-217F (25℃ )
	DIMENSION	2286838.8mm(LWH)
	PACKING	1.15Kg ; 12pcs/14.8Kg/0.8CUFT
NOTE	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
	2. Ripple and noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf and 47uf parallel capacitor.
	3. Tolerance: indudes set up tolerance, line regulation and load regulation.
	4. Please refer to "Driving Methods of LED Module."
	5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
	6. A-type only.
	7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, and FCC parti8.
	8. Length of set up time is measured at cold first start. Turning the power supply ON/OFF may increase the set up time.
	9. The power supply is considered a separate component that will operate in combination with the final equipment. Since EMC performance will be affected by its installation, the final equipment manufacturers must re-qualify EMC Directives on the installed product.
	10. Refer to warranty statement.
	11 .To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch that's not permanently connected to the main system.

Downloads